Everyone has got their unique way of thinking when it comes to Installing A Bathtub.
Installing a tub isn't specifically rocket science, however it does need strong plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a new one is additionally a reasonably hard job. If the old bathtub is conveniently accessible, the task can move quickly; if you need to open up a wall to remove the old bathtub and also place the brand-new bath tub, the task is much harder. In either situation, the project is within a residence handyman's skills, although you will need an assistant to vacate the old bathtub as well as set in the brand-new one. Make certain you have certified on your own for the task and are comfortable trying it. Rather than working with a contractor to take over a halfway-completed task, it is better to think about employing one before you begin. Possibilities are you may require a specialist plumber to make tube connections.
This short article will certainly aid you mount a brand-new bath tub in your restroom if you have actually currently purchased a brand-new tub and don't need to change the setup of your previous supply of water pipelines.
Your devices and also product checklist need to make up the following:
Preparing for the Installation
To start with, the supporting framework provided with the bathroom should be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps device to avoid stress on the bath tub.
Fit the adaptable faucet ports to the bottom of both taps using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its final position.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water supply. After doing so, switch on the taps to drain pipes any water remaining in the system. The procedure of removing the existing faucets can be quite troublesome due to the limited gain access to that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have been removed, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from transforming throughout this process. When the faucets have been removed, the holes in the bath/basin will have to be cleansed of any old securing substance.
Prior to carrying on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Setting up the Tub
Using the two wooden boards under its feet, position the bathtub in the called for position. The wood boards are helpful in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four small factors.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub until the level checks out degree.
To set up taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipe by making a compression sign up with; then do the very same for the various other tap.
Switch on the water and inspect all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Load the tub and also inspect the overflow electrical outlet and also the regular outlet for leakages.
Finally, deal with the bath paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bathtub ought to wait up until the bathtub has been utilized a minimum of when as this will resolve it into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin making certain that the washing machines remain in place in between the tap as well as the sink. Protect the faucet in place with the supplier supplied backnut. Once the faucet is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal tap ports. The former kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split an inflexible seal, creating the water to penetrate the wall in between the bath and the tiling, leading to problems with moisture and feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your components and fittings. They are offered in tubes and also cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before sealing, to permit the activity experienced when the tub is in usage. The sealant can break relatively very early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly offered on the market. It is suggested to fit the ceramic tiles utilizing water-resistant or water-proof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our piece about A Step-by-Step Guide to Installing a Bathtub. Thanks a ton for taking a few minutes to browse our short article. Feel free to take the opportunity to share this entry if you appreciated it. Thank-you for taking the time to read it.
Expertise on line!